{"id":3502,"date":"2025-09-02T17:17:30","date_gmt":"2025-09-02T09:17:30","guid":{"rendered":"https:\/\/taichungbro.com\/?p=3502"},"modified":"2025-09-02T17:17:31","modified_gmt":"2025-09-02T09:17:31","slug":"o-ring","status":"publish","type":"post","link":"https:\/\/www.taichungbro.com\/en\/2025\/09\/02\/o-ring\/","title":{"rendered":"O-ring design \u2013 How to choose the groove size, compression ratio, and hardness?"},"content":{"rendered":"<hr class=\"wp-block-separator has-alpha-channel-opacity is-style-wide\"\/>\n\n\n\n<div class=\"wp-block-rank-math-toc-block\" id=\"rank-math-toc\"><h2>Table of Content<\/h2><nav><ul><li class=\"\"><a href=\"#\u63a5\u89f8\u61c9\u529b\u3001\u6750\u6599\u7279\u6027\u8207\u58d3\u529b\u8f14\u52a9\">Contact stress, material properties and pressure assistance<\/a><\/li><li class=\"\"><a href=\"#\u8a2d\u8a08\u7a97\u53e3\u4e00\u89bd\">Design window overview<\/a><ul><li class=\"\"><a href=\"#a-\u58d3\u7e2e\u7387\u3001\u586b\u5145\u7387\u8207\u4f38\u5f35\u5efa\u8b70\">A. Compression Ratio, Fill Ratio, and Elongation Recommendations<\/a><\/li><li class=\"\"><a href=\"#b-\u6750\u6599\u8207\u786c\u5ea6\u901f\u67e5\uff08\u5e38\u898b\u914d\u5c0d\uff09\">B. Quick Reference for Materials and Hardness<\/a><\/li><li class=\"\"><a href=\"#c-\u58d3\u529b-\u9593\u9699-\u786c\u5ea6\uff1a\u662f\u5426\u9700\u8981\u5099\u7528\u74b0\uff08-backup-ring\uff09\">C. Pressure \u00d7 Clearance \u00d7 Hardness: Is a spare ring required?<\/a><\/li><li class=\"\"><a href=\"#d-\u8868\u9762\u7c97\u7cd9\u5ea6\u8207\u88dd\u914d\u5c0e\u89d2\">D. Surface roughness and assembly chamfer<\/a><\/li><\/ul><\/li><li class=\"\"><a href=\"#\u5f9e\u58d3\u7e2e\u7387\u5230\u6e9d\u69fd\u6df1\u5bec\">From compression ratio to trench depth and width<\/a><ul><li class=\"\"><a href=\"#\u7bc4\u4f8ba\uff1a\u8ef8\u5411\u975c\u614b\u9762\u5bc6\u5c01\">Example A: Axial static surface seal<\/a><\/li><li class=\"\"><a href=\"#\u7bc4\u4f8bb\uff1a\u5f91\u5411\u5f80\u5fa9\u5bc6\u5c01\">Example B: Radial reciprocating seal<\/a><\/li><\/ul><\/li><li class=\"\"><a href=\"#\u5e38\u898b\u5931\u6548\u8207\u5c0d\u7b56\">Common Failures and Countermeasures<\/a><\/li><li class=\"\"><a href=\"#\u5be6\u52d9\u5c0f\u6487\u6b65\">Practical Tips<\/a><\/li><\/ul><\/nav><\/div>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity is-style-wide\"\/>\n\n\n\n<p class=\"wp-block-paragraph\">O-rings are the most unassuming yet most life-saving components in industrial seals. From pneumatic cylinders and hydraulic valves to vacuum chambers, as long as the &quot;groove size, compressibility, and hardness&quot; are chosen correctly, yield and lifespan will increase; conversely, a difference of just a few percentage points can immediately lead to leakage, tombstoning torsion, and extrusion seizure. This article uses engineer-friendly tables and formulas to organize the design windows for static axial seals, radial reciprocating seals, and rotary seals, and demonstrates how to deduce the groove depth from the &quot;target compressibility,&quot; determine the groove width using the &quot;fill rate,&quot; and then determine whether to add a spare ring using &quot;pressure \u00d7 clearance \u00d7 hardness.&quot;<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"\u63a5\u89f8\u61c9\u529b\u3001\u6750\u6599\u7279\u6027\u8207\u58d3\u529b\u8f14\u52a9\">Contact stress, material properties and pressure assistance<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">O-rings rely on the contact stress generated by the compression of an elastomer to create a seal. Pressing the O-ring into a slightly shallower groove creates pre-compression; the contact stress is higher than the medium pressure and microscopic roughness peaks, thus blocking leakage microchannels. System pressure further pushes the O-ring towards the low-pressure side, forming a so-called &quot;pressure-assisted seal.&quot; Therefore, under appropriate compression ratios, increased pressure actually results in a tighter seal. The elastomer is a viscoelastic material: it behaves like a spring in the short term, but creep and permanent compression set occur over a long period. Therefore, the O-ring cannot be squeezed too tightly; otherwise, thermal expansion and medium swelling will leave no room for expansion. On the other hand, under high pressure, the O-ring will be squeezed into the gap. If the hardness is too low or the gap is too large, it will be sheared. Temperature changes the modulus and permanent compression set; the medium causes volume swelling or extracts plasticizers, altering hardness and dimensions. In summary, you need to manage four things simultaneously: compression ratio (% to establish contact stress), fill ratio (% to maintain volume margin), gap E (to resist extrusion), and material\/hardness (corresponding to temperature and medium). These four factors are interconnected and form the core of O-ring design.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"\u8a2d\u8a08\u7a97\u53e3\u4e00\u89bd\">Design window overview<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"a-\u58d3\u7e2e\u7387\u3001\u586b\u5145\u7387\u8207\u4f38\u5f35\u5efa\u8b70\">A. Compression Ratio, Fill Ratio, and Elongation Recommendations<\/h3>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Application:Application:<\/th><th>Compression ratio % <\/th><th>Fill rate % <\/th><th>O-ring inner diameter stretch %<\/th><th>illustrate<\/th><\/tr><\/thead><tbody><tr><td>Static axial seal (flange\/vacuum)<\/td><td>20\u201330 (25 is commonly used)<\/td><td>\u226485<\/td><td>0\u20132<\/td><td>High contact stress is required, and friction is less of a concern.<\/td><\/tr><tr><td>Static radial seal (plug\/hole plug)<\/td><td>15\u201325<\/td><td>\u226485<\/td><td>1\u20133<\/td><td>Pay attention to the chamfering during assembly to avoid scratches.<\/td><\/tr><tr><td>Reciprocating dynamic seal (piston rod\/hydraulic cylinder)<\/td><td>8\u201315 (10\u201312 are commonly used)<\/td><td>\u226480<\/td><td>\u22643 (1\u20132 are commonly used)<\/td><td>Balancing wear and friction<\/td><\/tr><tr><td>Low-speed rotary seal<\/td><td>2\u20135<\/td><td>\u226475<\/td><td>\u22642<\/td><td>Minimize compression and reduce heat generation<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\"><sub>Note: Fill rate = O-ring cross-sectional area \/ groove area; leaving blank space can absorb thermal expansion and swelling.<\/sub><\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"b-\u6750\u6599\u8207\u786c\u5ea6\u901f\u67e5\uff08\u5e38\u898b\u914d\u5c0d\uff09\">B. Quick Reference for Materials and Hardness<\/h3>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Material<\/th><th>Typical hardness<\/th><th>Temperature range<\/th><th>Specializing in media<\/th><th>not applicable<\/th><th>Usage Notes<\/th><\/tr><\/thead><tbody><tr><td>NBR<\/td><td>70A (General Purpose)<\/td><td>-30\u2013100\u00b0C<\/td><td>Oil, fuel<\/td><td>strong oxidants, ozone<\/td><td>Pneumatic\/hydraulic universal preferred<\/td><\/tr><tr><td>FKM (such as Viton)<\/td><td>70\/75A<\/td><td>-20\u2013200\u00b0C<\/td><td>Oil, solvent, chemical<\/td><td>amines, hot water vapor<\/td><td>High-temperature chemical environment<\/td><\/tr><tr><td>EPDM<\/td><td>70A<\/td><td>-50\u2013150\u00b0C<\/td><td>Water, steam, alcohol<\/td><td>mineral oil<\/td><td>Water system, cleaning line<\/td><\/tr><tr><td>VMQ (Silicone)<\/td><td>60\u201370A<\/td><td>-60\u2013200\u00b0C<\/td><td>Air, food and medicine<\/td><td>oil medium<\/td><td>Low temperature, food grade<\/td><\/tr><tr><td>FFKM<\/td><td>70\u201380A<\/td><td>0\u2013260\u00b0C\u2191<\/td><td>Almost all durable<\/td><td>Extremely high cost<\/td><td>Semiconductor\/Strong Corrosion<\/td><\/tr><tr><td>Hardness selection: 70A is universal; 80\u201390A is suitable for high pressure\/large gap; 50\u201360A is used for low pressure vacuum or when low clamping force is required.<\/td><td><\/td><td><\/td><td><\/td><td><\/td><td><\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"c-\u58d3\u529b-\u9593\u9699-\u786c\u5ea6\uff1a\u662f\u5426\u9700\u8981\u5099\u7528\u74b0\uff08-backup-ring\uff09\">C. Pressure \u00d7 Clearance \u00d7 Hardness: Is a spare ring required?<\/h3>\n\n\n\n<figure class=\"wp-block-table aligncenter\"><table class=\"has-fixed-layout\"><thead><tr><th>Medium pressure<\/th><th>70A Maximum allowable clearance E<\/th><th>90A Maximum allowable clearance E<\/th><th>suggestion<\/th><\/tr><\/thead><tbody><tr><td>\u22641 MPa (10 bar)<\/td><td>\u22640.25 mm<\/td><td>\u22640.35 mm<\/td><td>Most do not require a spare ring<\/td><\/tr><tr><td>1\u20135 MPa (10\u201350 bar)<\/td><td>\u22640.15 mm<\/td><td>\u22640.25 mm<\/td><td>90A or single-sided spare ring<\/td><\/tr><tr><td>5\u201320 MPa (50\u2013200 bar)<\/td><td>\u22640.05\u20130.10 mm<\/td><td>\u22640.15 mm<\/td><td>A spare ring must be added; clearance must be controlled.<\/td><\/tr><tr><td>&gt;20 MPa (&gt;200 bar)<\/td><td>\u2014<\/td><td>\u22640.05\u20130.10 mm<\/td><td>Dual backup rings or alternative U-shaped cups<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\"><sub>Note: E is the radial clearance on the pressure side (half the difference between the piston rod and the guide sleeve, or between the plug and the hole).<\/sub><\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"d-\u8868\u9762\u7c97\u7cd9\u5ea6\u8207\u88dd\u914d\u5c0e\u89d2\">D. Surface roughness and assembly chamfer<\/h3>\n\n\n\n<figure class=\"wp-block-table aligncenter\"><table class=\"has-fixed-layout\"><thead><tr><th>Location<\/th><th>Ra is recommended<\/th><th>Chamfer\/Bevel<\/th><th>Rounded corners<\/th><\/tr><\/thead><tbody><tr><td>Dynamic seal contact surface (shaft\/bore)<\/td><td>0.2\u20130.4 \u00b5m<\/td><td>15\u201320\u00b0<\/td><td>R0.2\u20130.5<\/td><\/tr><tr><td>Trench bottom\/sidewall (moving)<\/td><td>0.2\u20130.8 \u00b5m<\/td><td>\u2014<\/td><td>R0.2<\/td><\/tr><tr><td>Trench bottom\/sidewalls (static)<\/td><td>0.8\u20131.6 \u00b5m<\/td><td>\u2014<\/td><td>R0.2<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"\u5f9e\u58d3\u7e2e\u7387\u5230\u6e9d\u69fd\u6df1\u5bec\">From compression ratio to trench depth and width<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">We use &quot;section diameter CS&quot; as the core parameter.<br>Compression ratio %: s% = (CS \u2212 H)\/CS \u00d7 100%, where H is the effective depth of the trench.<br>Filling ratio % (approximate for axial sealing): f% = A_or(W\u00d7H) \u00d7 100%, A_or = \u03c0\u00b7CS\u00b2\/4, where W is the groove width.<br>The steps are as follows:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Choose the CS (common CS: 1.78, 2.62, 3.53, 5.33 mm, etc.) and s% target according to the application.<\/li>\n\n\n\n<li>Calculate H = CS\u00b7(1 \u2212 s).<\/li>\n\n\n\n<li>Given a target fill rate f (static \u2264 85%, dynamic \u2264 80%), calculate W = A_or\/(H\u00b7f).<\/li>\n\n\n\n<li>Check if the pressure side clearance E meets the requirements of the table above; if not, replace with a higher hardness ring\/add a spare ring\/converging fit.<\/li>\n\n\n\n<li>Add allowances for thermal expansion and swelling (usually estimated by volumetric swelling 3\u201310% depending on the medium), and further relax W or lower s% if necessary.<\/li>\n<\/ol>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"\u7bc4\u4f8ba\uff1a\u8ef8\u5411\u975c\u614b\u9762\u5bc6\u5c01\">Example A: Axial static surface seal<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Material selection: VMQ 60A (low-pressure clamping, vacuum clean).<\/li>\n\n\n\n<li>CS = 3.53 mm, target s = 25%. \u21d2 H = 3.53\u00d7(1\u22120.25)=2.65 mm.<\/li>\n\n\n\n<li>Dynamics are not important, so we take f=0.80.<\/li>\n\n\n\n<li>A_or = \u03c0\u00b73.53\u00b2\/4 \u2248 9.79 mm\u00b2 \u21d2 W = 9.79\/(2.65\u00d70.80)=4.62 mm.<\/li>\n\n\n\n<li>Design: H\u22482.65 mm, W\u22484.6\u20134.8 mm, corner radius R0.2, contact surface Ra 0.8\u20131.6 \u00b5m.<\/li>\n\n\n\n<li>If the flange will be baked to 150\u00b0C, the estimated volume expansion + swelling is 3\u20135%, so W can be relaxed by 0.1\u20130.2 mm.<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"\u7bc4\u4f8bb\uff1a\u5f91\u5411\u5f80\u5fa9\u5bc6\u5c01\">Example B: Radial reciprocating seal<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Medium: 0.6 MPa air; low friction desired; NBR 70A.<\/li>\n\n\n\n<li>CS = 2.62 mm, target s = 12%. \u21d2 H = 2.62\u00d7(1\u22120.12)=2.306 mm.<\/li>\n\n\n\n<li>f is taken as 0.75 (dynamic seal). A_or \u2248 5.39 mm\u00b2 \u21d2 W = 5.39\/(2.306\u00d70.75)=3.12 mm.<\/li>\n\n\n\n<li>Pressure \u22641 MPa, allowable E \u22640.25 mm; design sliding fit to control E within 0.1\u20130.15 mm for greater stability.<\/li>\n\n\n\n<li>Surface finish: Shaft Ra 0.2\u20130.4 \u00b5m; 20\u00b0 chamfer at the assembly end and apply a thin layer of grease to prevent twisting.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><sub>Note: When radial sealing, the O-ring is placed in the groove of the piston or guide sleeve. The above approximate area can still be used as a design starting point; the final confirmation is made by thermal cycling and pressure resistance tests of the sample.<\/sub><\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"\u5e38\u898b\u5931\u6548\u8207\u5c0d\u7b56\">Common Failures and Countermeasures<\/h2>\n\n\n\n<figure class=\"wp-block-table aligncenter\"><table class=\"has-fixed-layout\"><thead><tr><th>Phenomenon<\/th><th>main reason<\/th><th>Quick Countermeasures<\/th><\/tr><\/thead><tbody><tr><td>Leakage (low pressure)<\/td><td>Insufficient compression ratio, surface too rough<\/td><td>s%+5, replace with finer Ra, check for assembly scratches<\/td><\/tr><tr><td>Leakage (only occurs when pressure is increased)<\/td><td>Squeeze out bite<\/td><td>Reduce E, replace with 90A, add a spare ring, and reduce gap thermal expansion.<\/td><\/tr><tr><td>Compression permanent deformation<\/td><td>Excessive filling rate\/high temperature residence<\/td><td>Reduce f% to \u226480\u201385, select heat-resistant materials, and shorten clamping time.<\/td><\/tr><tr><td>Spiral failure<\/td><td>Uneven friction of dynamic seal, grooves too narrow<\/td><td>W widened 10\u201320%, improved lubrication, chamfered angle.<\/td><\/tr><tr><td>Wear out too quickly<\/td><td>Excessive compression ratio, excessively rough surface<\/td><td>s% was downgraded by 2\u20135, and Ra decreased to 0.2\u20130.4 \u00b5m.<\/td><\/tr><tr><td>swelling and softening<\/td><td>Material incompatibility<\/td><td>Check chemical compatibility, modified EPDM\/FKM\/FFKM<\/td><\/tr><tr><td>Low temperature hardening<\/td><td>The glass transition temperature of the material is too high.<\/td><td>Modified VMQ\/EPDM material, reduced friction load<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"\u5be6\u52d9\u5c0f\u6487\u6b65\">Practical Tips<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li>First, consider the temperature and medium: When the temperature is high or the medium is in contact with solvents, prioritize a more conservative filling rate (dynamic seal 70\u201375%).<\/li>\n\n\n\n<li>Hardness is not just about pressure: if you change to 90A but experience micro-leakage, it is usually due to insufficient compression ratio or unsuitable surface roughness; hardness is only for preventing extrusion.<\/li>\n\n\n\n<li>Spare ring directionality: for unilateral pressure, install it on the pressure side; for bidirectional pressure, use two spare rings. PTFE spare rings have high temperature resistance and low friction.<\/li>\n\n\n\n<li>Assembly must include chamfering: without chamfering, the lip edge is most easily scratched; a chamfer of 15\u201320\u00b0 with an radius of 0.3 is very effective.<\/li>\n\n\n\n<li>Vacuum-preferred silicone\/low hardness: To improve contact stress uniformity and micro-adhesion, 60A silicone is often more stable than 70A NBR.<\/li>\n\n\n\n<li>Before mass production, three things need to be done: low\/normal\/high temperature dimensional measurement, static\/dynamic pressure holding test, and compression set evaluation after thermal cycling.<\/li>\n<\/ul>\n\n\n\n<p class=\"has-text-align-center wp-block-paragraph\">\u2014\u2014<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">O-ring design may seem like a simple matter of &quot;putting it in and pressing it down,&quot; but it actually involves a balance of contact stress, viscoelasticity, pressure assistance, and geometric volume. By grasping three key points\u2014establishing a basic seal using &quot;compression ratio,&quot; allowing space for thermal expansion and swelling using &quot;fill ratio,&quot; and determining whether to add a spare ring using &quot;pressure \u00d7 gap \u00d7 hardness&quot;\u2014and combining this with appropriate materials and surface roughness, the risk of failure can be significantly reduced. In short, starting with the table values in this article, and using the two small examples above to deduce your groove depth and width, and finally using samples for temperature and pressure stress testing and correction, your O-ring design can be quickly implemented, avoiding both excessively conservative designs leading to excessive friction and overly aggressive designs that result in extrusion failure.<\/p>\n\n\n\n<div style=\"height:var(--wp--preset--spacing--30)\" aria-hidden=\"true\" class=\"wp-block-spacer\"><\/div>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity is-style-wide\"\/>\n\n\n\n<h5 class=\"wp-block-heading has-text-align-center\" id=\"\u60f3\u4e86\u89e3\u6709\u95dc\u7ba1\u87ba\u7d0b\u3001\u76f4\u87ba\u7d0b\u3001\u9310\u87ba\u7d0b\u3001\u5c3a\u5bf8\u8868\u793a\u3001\u82f1\u5236\u7ba1\u87ba\u7d0b\u3001\u516c\u5236\u7ba1\u87ba\u7d0b\u7684\u77e5\u8b58\u55ce\uff1f-\u5ef6\u4f38\u95b1\u8b80\uff1a\u300a\u7ba1\u87ba\u7d0b\u767e\u767e\u7a2e-\u4f60\u90fd\u8a8d\u8b58\u55ce-\u300b\">Want to learn about rubber FFKM, hardware, materials, and other related information about sealing rings? <br>Further Reading :<a href=\"https:\/\/www.taichungbro.com\/en\/2025\/07\/04\/ffkm\/\" data-type=\"link\" data-id=\"https:\/\/taichungbro.com\/2023\/10\/28\/screw\/\" target=\"_blank\" rel=\"noopener\">Why is FFKM, a perfluorinated rubber, called the &quot;King of Rubbers&quot;? The secrets and applications of sealing in high-temperature and chemical environments.<\/a><\/h5>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity is-style-wide\"\/>\n\n\n\n<div style=\"height:11px\" aria-hidden=\"true\" class=\"wp-block-spacer\"><\/div>","protected":false},"excerpt":{"rendered":"<p>A ready-to-use O-ring design guide: This guide teaches you how to deduce groove depth and width using compression ratio and fill rate, and how to select the right O-ring based on pressure \u00d7 clearance \u00d7 hardness. It includes commonly used tables, formulas, and static\/dynamic seal examples, along with common failure strategies to help you quickly complete mass-production-grade seal designs.<\/p>","protected":false},"author":2,"featured_media":3503,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[45],"tags":[376,378,377,274],"class_list":["post-3502","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industrial-knowledge","tag-o","tag-378","tag-377","tag-274"],"acf":[],"_links":{"self":[{"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/posts\/3502","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/comments?post=3502"}],"version-history":[{"count":0,"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/posts\/3502\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/media\/3503"}],"wp:attachment":[{"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/media?parent=3502"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/categories?post=3502"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.taichungbro.com\/en\/wp-json\/wp\/v2\/tags?post=3502"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}