How to set the pressure holding and position switching? Techniques to avoid shrinkage and flash.

兩個白色塑膠框放在灰色背景,左邊有飛邊缺陷,右邊有明顯縮水凹陷


In plastic injection molding, packing/holding and volume/pressure (V/P) switch are two key parameters that determine the product's appearance and dimensional accuracy. Packing/holding compensates for molten plastic cooling and shrinkage, preventing shrinkage and dents; the V/P switch determines the timing of the transition from speed control to pressure control, affecting infill integrity and internal stress. Improper settings can lead to shrinkage, flash, and even stress cracking. This article will introduce the principles, setting methods, and reference data for packing/holding and V/P switch to help engineers quickly optimize molding parameters.

Basic principles of pressure holding and position switching

In injection molding, the filling stage is typically speed-controlled, filling the cavity to approximately 95–98 %. As the molten material advances, the pressure within the cavity rises rapidly, transitioning to a holding pressure stage when the cavity is nearly full, where pressure control compensates for material cooling and shrinkage.

  • Switching positions too early: The cavity is not fully filled, which may lead to short shots, shrinkage, or material shortage.
  • Switching positions too late: Excessive pressure can easily cause flash, stress concentration, and even mold damage. Ideally, the switching point should be just before the molten plastic reaches the end of the gate to ensure that the holding pressure can be effectively transmitted.

Method for determining the location setting

There are two common settings in engineering:

  1. 體The fill ratio is calculated based on the screw position, and is usually set at 95–98% of the cavity volume.
  2. Pressure method (mold pressure curve): Observe the mold pressure curve and switch before reaching the peak value so that the pressure holding can immediately compensate for the contraction.

Different plastics recommended switching ratio table(Reference value):

MaterialWe recommend switching the ratio (fill completion rate).
PP96–98%
ABS95–97%
PC97–98%
POM96–97%

Pressure holding pressure and time adjustment strategy

  • Holding pressure
    • Too low → Product shrinkage, insufficient density.
    • Excessive heat leads to increased flash, internal stress, and a higher risk of embrittlement.
    • It is generally recommended to set it to 50–80 % of the material flow pressure.
  • Holding time
    • Continue at least until the gate is closed to prevent material backflow.
    • Test method: Gradually reduce the holding time until the product weight drops significantly, which is the gate closure point.

Case Studies and Data Analysis

The effect of holding pressure and time on defects (assuming ABS housing)

Holding pressure / Holding timeAverage weight (g)Shrinkage ratioFlanged edge situation
60% / 4s102.0高無
70% / 4s102.4低無
85% / 4s102.5低slight
85% / 2s101.8中slight

In one ABS housing production process, the initial switching position was set to 99%, and the holding pressure was 85%. While the appearance was full, the flash rate reached 12%. After adjustment: the switching position was changed to 96%, the holding pressure was reduced to 75%, and the holding time was maintained at 4 seconds. The flash rate decreased to 1%, and the shrinkage problem was completely eliminated. This proves that switching too late and excessive pressure can cause unnecessary appearance defects.


Setting the holding pressure and switching position is not just about adjusting numbers; it's the core of molding stability. In principle, the appropriate switching position should be determined first, then the holding pressure and time should be fine-tuned, with product weight and appearance used as verification criteria. Each type of plastic, product thickness, and mold design is different, so parameters must be gradually optimized through trial molding and data analysis. Establishing an internal "material and product parameter database" can significantly shorten trial molding time and reduce defect rates.


Would you like to learn about plastic injection molding, injection defects, and solutions for short shots?
Further Reading :《Injection Molding - Short Shot Countermeasures》

Recommended Posts